
Long optical path for increased sensitivity, in three lengths
Extended version of the PG11 explosion-proof infrared point detector. Its longer optical path increases sensitivity, and it comes in 15, 35, or 50 cm lengths for duct, pipe, and double-wall pipe mounts. It has the same lifetime factory calibration, T90 under 1.5 seconds, and SIL 2 design as the PG11.
A long optical path increases sensitivity for HVAC intakes, gas turbine enclosures, double-wall (double-skin) LNG/LPG pipe, and other applications that need early warning.
Comes in three lengths: short (15 cm), medium (35 cm), and long (50 cm), to fit different duct, pipe, and enclosure installations.
Factory calibrated for life, so there is no field calibration. Built-in condition monitoring runs a continuous health check and tells the operator when anything needs attention.
The solid-state infrared SafeSource™ carries a 15-year warranty, and the detector has a 6-year warranty. T90 is under 1.5 seconds, with OptoBAS™ baseline accuracy and heated sapphire optics.
Designed for SIL 2/SC3 systems (SIL 3 in 1oo2 redundancy) and rated ATEX/IECEx Ex db eb ib IIC T5 Gb, with marine approvals from MED, BV, LR, DNV GL, and ABS.
4–20 mA source or sink output with HART 7, plus the OptoCom™ module for application-specific digital protocols and DCS integration.
From the PGE11 datasheet (022-80102-ML R02). Contact GDS for help with application and positioning.
Duct-mounted detection in air intakes and ventilation systems.
Combustible gas detection in turbine enclosures and ventilation ducts.
Monitoring of double-wall (double-skin) LNG and LPG pipe.
Any application where a longer optical path gives earlier warning.
The PGE11 comes in three lengths.
15 cm
35 cm
50 cm. Reduced vibration range; contact GDS for details.
0–100% LEL, or 0–100% by volume
0–100% LEL
0–100% by volume (CH₄ in a CO₂ background)
0–100% by volume
Contact GDS to specify.
For most standard JIS, DIN, and ANSI flanges.
For field testing. Available in lengths to match each PGE11 version.
Fits most existing installation footprints to simplify retrofits. A pole mount kit with U-bolts for 3 in. and 4 in. poles is also available.
A test point you route to the detector with standard tubing or piping, for detectors in inaccessible or remote locations.
Typical facilities and process areas where this product protects people and assets.
Key parameters below. For full datasheets, ratings, and ordering options, contact GDS.
| Manufacturer | Optronics |
| Category | Infrared Point Gas Detectors |
| Technology | Solid-state infrared SafeSource™, temperature compensated; long optical path for increased sensitivity |
| Gases and ranges | Methane 0–100% LEL or 0–100% vol · Propane, ethylene, butane 0–100% LEL · Biogas (CH₄ in CO₂) 0–100% vol · CO₂ 0–100% vol |
| Configurations | Short 15 cm · Medium 35 cm · Long 50 cm (reduced vibration range) |
| Calibration | Factory calibrated; no field calibration needed |
| Self-test | Continuous health check of all important hardware and software functions |
| Accuracy | ±3% FS |
| Repeatability | ±1% FS |
| Response time | T90 = 1.5 s |
| Signal output | 4–20 mA current source or sink; warnings and faults signalled below 4 mA · HART 7 for maintenance and configuration · OptoCom™ for application-specific digital protocols |
| Operating temperature | −40 to +65 °C (−40 to +149 °F) · Desert version −40 to +75 °C (−40 to +167 °F) · Arctic version −60 to +65 °C (−76 to +149 °F) |
| Storage temperature | −60 to +75 °C (−76 to +167 °F) |
| Humidity | 0–100% RH |
| Vibration | Resistant to shock and vibration up to 4 g (reduced range on the long version) |
| Ingress protection | IP66 / IP67 |
| Housing | 316L stainless steel |
| Weight and dimensions | Under 4 kg (8.8 lb); 775 × 120 × 120 mm |
| Field wiring | Stranded or solid wire up to 2.5 mm² |
| Cable entries | Two M20 as standard; M25, ½" NPT, and ¾" NPT on request |
| Power | 18–50 V DC; under 3.5 W average (under 5 W, Arctic version); soft boot with 1 A max. current spikes |
| Hazardous area | ATEX/IECEx Ex db eb ib IIC T5 Gb |
| Marine approvals | MED, BV, LR, DNV GL, ABS |
| Safety integrity | SIL 2/SC3 to IEC 61508 (SIL 3 in 1oo2 redundancy) |
| Warranty | 6 years; 15 years on the SafeSource™ |
| Approvals | ATEX, IECEx, SIL 2, MED, DNV |
Tell us the details and we'll come back with pricing, availability, and lead time — usually the same day.
Others in the Infrared Point Gas Detectors range and from Optronics.
Send us the details and our team will get you a quote and lead time — usually the same day.
Request a Quote